only1wei asked:


Hooks? Above this c? mara CCTV / surveillance (the? of SONY? 1 / 3? ESTUPENDO TEN? A CCD La C? of MARA COLOR WEATHER PROOF D? AY OF THE NIGHT WITH 520 TVL 36 IR LEDs ) with the video cassette recorder of the length of time today and it works just fine. but somehow at the center of the monitor, an error appeared 3? and not leave?. ? Can anyone tell me what? went wrong, and c? mo make out? Thanks a lot.

Joshua K asked:


DVR be? Av? Deo of recording? A n c? Mara activated movement that monitors input / output of an individual building. DVR tendr? to carry out the data for 30 d? as and after being s? held on to the tape.

xnhor asked:


Do you want to install cameras in my house, anyone know of a CCTV site where I can see the CCTV for free?

dljewer asked:

Cre? this v? deo using my Logitech QuickCam software

cctvcamerapros asked:

WWW.CCTVCAMERASPROS.COM - C? Mo Press-On BNC plug connectors to RG59 CCTV Cable. Reception? Navarre the instructions? N of v? Deo the pros of the c? Mara's CCTV. In this v? Deo you teach? AREM ac? Mo encrespadura of a tie in the BNC connector to a cable siam? S of CCTV RG59. Step one. Grab one end of your cable RG59. Using a pair of separate cortaalambres the RG59 cable coaxil of the 18 transmission cables? N calibrator. Using the barrel of a piece of encrespadura in BNC connector, measure cu? Nt of the jacket of the cable you need? peel. You want to peel away the length of the large encrespadura in the piece is that? about half of its integral. Then, using a cable splitter or cortaalambres tool peels rubber sheilding external RG59. Be careful not to cut the braided copper wire inside the first layer of insulation. After? S, move the copper wire twisted to one side. You can twist the wire as it crossed together. Then, using pelacables remove internal shield RG59. This will expose? thin copper wire that is used for communication? n CCTV video. Sometimes a small edge or cable shields to the left in RG59 separ when you? RG59 the wire gauges 18. Using a razor blade, carefully remove the song because you can prevent the slide portion? N barrel of the BNC connector on the cable. Be careful not to remove too. Cerci? Make sure you do not expose any copper wires crossed. After? S, straighten the two pieces of copper wire twisted so that we can slide the barrel connector on the cable RG59. Put the piece of the barrel of the BNC connector on the cable, small or side first and slide the barrel over the cable like RG59. Resb? M just parallel? S all? the portion? n peeled whole cable. Separate the braided copper wire again to make sure it not? Est l? touching the copper wire internally. This is very important. If the wire is crossed? touching the wire in the communication? No, the cable does not work? correctly and may even interfere with other cables connected to its monitoring system. Slide the piece of var? N BNC connector on the two pieces of RG59 cable. The push on the barrel piece BNC male connector and make sure it is? rested firmly together. Using a tool that RG-59 press, press firmly on the connector cable. Some tools that have pressed the cable m? S setting in one of them. Est? sure to use the section? n RG59. After? S connected to confirm that is? tied securely. Follow this same process to attach a BNC encrespadura of power at the other end of the RG59 cable. If you have any questions about this v? Deo please visit our Web site or call our n? Mere free.

brumgeeza asked:

see a ghostly figure of a man in the back of the room the amount of cctv left a morgue